Why Understanding Essential Plumbing Skills is Crucial For Installing a Bathtub
Why Understanding Essential Plumbing Skills is Crucial For Installing a Bathtub
Blog Article
They are making a few great points related to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround overall in this content followed below.
Setting up a tub isn't specifically brain surgery, however it does need solid plumbing, carpentry, as well as often, tiling skills. Changing an old bathtub with a new one is likewise a moderately challenging job. If the old tub is easily obtainable, the job can relocate rapidly; if you have to open a wall surface to get rid of the old bathtub as well as position the new bath tub, the job is much harder. In either instance, the job is within a house handyman's abilities, although you will certainly need an assistant to leave the old tub and also set in the brand-new one. Make sure you have actually qualified on your own for the task and also are comfortable attempting it. As opposed to hiring a contractor to take over a halfway-completed task, it is far better to think about utilizing one before you start. Opportunities are you might require a specialist plumber to make tube links.
This article will certainly assist you mount a brand-new tub in your shower room if you have actually already gotten a brand-new tub as well as do not require to alter the arrangement of your previous supply of water pipes.
Your devices as well as product list should make up the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, after that the first thing you must do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The process of getting rid of the existing faucets can be quite troublesome as a result of the restricted access that is commonly the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly originate from the pipes. When the supply pipes have actually been removed, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will have to be cleansed of any type of old securing substance.
Before moving on to fit the brand-new taps, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin ensuring that the washing machines are in place between the faucet and the sink. Protect the tap in position with the manufacturer offered backnut. When the faucet is securely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous kind should be connected to the tap ends first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Setting up the Bath tub
Making use of both wood boards under its feet, put the tub in the needed position. The wooden boards are helpful in uniformly spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto four small factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by inspecting the spirit level as well as changing the feet on the tub up until the spirit level reviews level.
To mount faucets, fit the bottom of the furthest flexible tap adapter to the suitable supply pipeline by making a compression sign up with; then do the same for the other tap.
Turn on the water system and examine all joints as well as brand-new pipework for leaks and also tighten them if required. Fill the bath tub as well as additionally inspect the overflow outlet as well as the regular outlet for leaks.
Finally, repair the bath paneling as described in the maker's instruction manual. Tiling as well as securing around the bathtub needs to wait till the tub has been made use of a minimum of once as this will certainly settle it into its final placement.
Preparing for the Installment
First of all, the supporting framework provided with the bath should be fitted (if called for) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to make certain that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to avoid strain on the bathtub.
Fit the versatile tap ports to the bottom of both taps making use of 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use every one of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be suited its final placement.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break an inflexible seal, triggering the water to pass through the wall surface between the bathroom as well as the tiling, resulting in difficulties with wetness as well as possible leaks to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and also installations. They are offered in tubes and also cartridges, as well as are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of drenched paper or soft rope. Remember to always fill the bath tub with water prior to securing, to enable the motion experienced when the bathtub remains in use. The sealer can split fairly early if you do not think about this movement before sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently offered on the marketplace. It is suggested to fit the floor tiles utilizing waterproof or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that blog entry on How to Install a Bathtub when doing a search on the search engines. I beg you take the time to distribute this page if you liked it. Thanks for your time spent reading it.
Immediate care? Call! Report this page